Skip navigation and go to content.
My Cart: 0 item(s)


Purchase Emblem - "PORSCHE"
  • Emblem - "PORSCHE" SKU: SKUEMBLA

    ★★★★★ ★★★★★ 5/5 Stars. (9 Reviews)
  • $80.00

  • Color:
  •  


"PORSCHE" emblem in black. An easy upgrade for any Porsche!

Each letter is independent, and can be positioned as needed. Comes with adhesive on the back-side of each letter, just clean the painted surface properly and apply. Each letter is around 4 cm wide, and 2 cm tall. Choose from matte black, high gloss black, or Agate Grey.

Note: No warranty on emblem adhesive, professional installation recommended. 

★★★★★ ★★★★★
5/5 Stars out of 9 Reviews
1
0
2
0
3
0
4
0
5
9
Great service
(Miami) | March 26th, 2021
Excellent service and great product
Emblem upgrade
(Greenbelt MD) | May 30th, 2020
Color is amazing!! I recommend this emblem upgrade to anyone that is trying to get out of the regular silver .
Perfect
(New Jersey) | March 26th, 2017
Matte black on Sapphire Blue Cayman. Total job took 30 mins.
Easy to install
(San Francisco) | September 14th, 2016
Easy change from chrome to black lettering on my Macan. Just outline the current letters on all four corners in blue masking tape. Pop off the letters with floss. Now remove the thick leftover sticky glue with your thumb nail. Clean the remaining glue with WD 40. Now clean off with alcohol and let dry. Align your new lettering in the blue letter boxes paying careful attention to the top line. Press hard and your done!
Brilliant
(Netherlands) | September 1st, 2016
Looks much better than chrome original emblem
Porsche Emblem
(pinehurst, nc) | August 17th, 2016
As described
Good Looking
| August 17th, 2016
for sporty looking matte black is best color
Black badges
(Raleigh NC) | July 20th, 2016
Replaced my chrome badges with the blacked out "GTS" version. Great look on the agate gray. Fit was perfect (had the dealer install with their template) Fast shipping, OE parts from Porsche, very happy with quality, fit, and look.
Porsche Emblem
(Cleveland Ohio) | April 29th, 2016
Great product. Super easy to install. People on the web used all kinds of stupid ways to put these on. Took less than 5 minutes my way and they are perfectly aligned. The top of the letters are flat so this will be your install line, you don't need a bottom line. To measure the curve properly on the trunk, find where you want the line of the top of the letters to be (personal preference), Use a tape measure and measure that exact same measurement along the entire trunk using the back of the trunk lid as your starting point. Mark it with a pencil in about 20 spots on the trunk (lightly)! Use blue masking tape to joint your 20 spots together to make the curve. This is now the top line. Find the center for the first letter. Stick it on. Then go left and right after setting the first middle letter. Use a caliper to set the distance between the top (not bottom or middle again its a curve) of the letters. I used 0.865". Stick them on so the top is parallel to your tape. Take off your blue tape. FYI, clean the area with alcohol first to get them to stick properly. These logos are not installed straight because the trunk lid curves slightly. Looks factory on my car.
 

Review this Item

Emblem - "PORSCHE"
Click the stars to rate. 5 stars is the best.
All fields are required except "where you're from".
Your email is for verification purposes only and will NOT be published or shared. See our Privacy Policy. Thank you for your review!

Enter only the red text:  3Ry1131168Arq!